You are not logged in.
- Topics: Active | Unanswered
#1 2026-01-10 20:14:34
- drudox
- Member
- Registered: 2017-10-01
- Posts: 143
X failure with nvidia-590 and nvidia gtx970
Hello guys
I have this problem ..
hardware : i7-14700k / msi prob760-pII / and nvidia gtx 970 !!
after updating X doesn't start ! black screen .. just the tty ! I try to read the Xorg.0.log .. where there I figure out that the new nvidia-590 drivers no longer support my gpu and said to use the nvidia-580xx (available in aur) .. I followed this advice .. but nothing change ! ... Xorg only start if I delete xorg.conf (just in one display .. I have 3 screen )
/var/log/Xorg.0.log report this error:
[ 8.395] (EE) NVIDIA: Failed to initialize the NVIDIA kernel module. Please see the
[ 8.395] (EE) NVIDIA: system's kernel log for additional error messages and
[ 8.395] (EE) NVIDIA: consult the NVIDIA README for details.
[ 8.395] (EE) No devices detected.
[ 8.395] (EE)
Fatal server error:
[ 8.395] (EE) no screens found(EE)
[ 8.395] (EE)
Please consult the The X.Org Foundation support
at [url]http://wiki.x.org[/url]
for help.
[ 8.395] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 8.395] (EE)
[ 8.395] (EE) Server terminated with error (1). Closing log file.thanks in advance
Last edited by drudox (2026-01-10 20:16:16)
Offline
#2 2026-01-10 20:55:54
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 72,057
Re: X failure with nvidia-590 and nvidia gtx970
the new nvidia-590 drivers no longer support my gpu and said to use the nvidia-580xx
GTX970 should™ be a Maxwell chip so that's correct.
Please post the entire X11 log and the outputs of
dkms status; lspci -kSidenote:
Xorg only start if I delete xorg.conf
You're not supposed to have or require a static server config itfp. Post that file as well.
Offline
#3 2026-01-10 21:29:16
- drudox
- Member
- Registered: 2017-10-01
- Posts: 143
Re: X failure with nvidia-590 and nvidia gtx970
Thanks for reply
root@ubu24 /]# dkms status
[root@ubu24 /]# lspci -k
00:00.0 Host bridge: Intel Corporation Raptor Lake-S 8+12 - Host Bridge/DRAM Controller (rev 01)
DeviceName: Onboard - Other
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 7e29
lspci: Unable to load libkmod resources: error -2
00:01.0 PCI bridge: Intel Corporation Raptor Lake PCI Express 5.0 Graphics Port (PEG010) (rev 01)
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 7e29
Kernel driver in use: pcieport
00:02.0 Display controller: Intel Corporation Raptor Lake-S GT1 [UHD Graphics 770] (rev 04)
DeviceName: Onboard - Video
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 7e29
Kernel driver in use: i915
00:06.0 PCI bridge: Intel Corporation Raptor Lake PCI Express 4.0 Graphics Port (rev 01)
Kernel driver in use: pcieport
00:08.0 System peripheral: Intel Corporation GNA Scoring Accelerator module (rev 01)
DeviceName: Onboard - Other
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 7e29
00:0a.0 Signal processing controller: Intel Corporation Raptor Lake Crashlog and Telemetry (rev 01)
DeviceName: Onboard - Other
Kernel driver in use: intel_vsec
00:14.0 USB controller: Intel Corporation Raptor Lake USB 3.2 Gen 2x2 (20 Gb/s) XHCI Host Controller (rev 11)
DeviceName: Onboard - Other
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 7e29
Kernel driver in use: xhci_hcd
00:14.2 RAM memory: Intel Corporation Raptor Lake PCH Shared SRAM (rev 11)
DeviceName: Onboard - Other
00:16.0 Communication controller: Intel Corporation Raptor Lake CSME HECI #1 (rev 11)
DeviceName: Onboard - Other
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 7e29
Kernel driver in use: mei_me
00:17.0 SATA controller: Intel Corporation Raptor Lake SATA AHCI Controller (rev 11)
DeviceName: Onboard - SATA
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 7e29
Kernel driver in use: ahci
00:1c.0 PCI bridge: Intel Corporation Raptor Lake PCI Express Root Port #1 (rev 11)
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 7e29
Kernel driver in use: pcieport
00:1f.0 ISA bridge: Intel Corporation B760 Chipset LPC/eSPI Controller (rev 11)
DeviceName: Onboard - Other
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 7e29
00:1f.3 Audio device: Intel Corporation Raptor Lake High Definition Audio Controller (rev 11)
DeviceName: Onboard - Sound
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 9e29
Kernel driver in use: snd_hda_intel
00:1f.4 SMBus: Intel Corporation 700 Series Chipset SMBus Controller (rev 11)
DeviceName: Onboard - Other
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 7e29
Kernel driver in use: i801_smbus
00:1f.5 Serial bus controller: Intel Corporation Raptor Lake SPI (flash) Controller (rev 11)
DeviceName: Onboard - Other
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 7e29
Kernel driver in use: intel-spi
01:00.0 VGA compatible controller: NVIDIA Corporation GM204 [GeForce GTX 970] (rev a1)
Subsystem: ZOTAC International (MCO) Ltd. Device 1366
Kernel driver in use: nvidia
01:00.1 Audio device: NVIDIA Corporation GM204 High Definition Audio Controller (rev a1)
Subsystem: ZOTAC International (MCO) Ltd. Device 1366
Kernel driver in use: snd_hda_intel
02:00.0 Non-Volatile memory controller: Phison Electronics Corporation E12 NVMe Controller (rev 01)
Subsystem: Phison Electronics Corporation E12 NVMe Controller
Kernel driver in use: nvme
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8125 2.5GbE Controller (rev 05)
Subsystem: Micro-Star International Co., Ltd. [MSI] Device 7e29
Kernel driver in use: r8169Xorg.conf:
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 580.119.02
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0"
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection
Section "Files"
EndSection
Section "InputDevice"
# generated from default
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
# generated from default
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Unknown"
ModelName "Unknown"
Option "DPMS"
EndSection
Section "Device"
Identifier "Device0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Depth 24
EndSubSection
EndSectionOffline
#4 2026-01-10 21:36:57
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 72,057
Re: X failure with nvidia-590 and nvidia gtx970
So "dkms status" is empty, suggesting nvidia-580xx-dkms isn't installed but then
01:00.0 VGA compatible controller: NVIDIA Corporation GM204 [GeForce GTX 970] (rev a1)
Subsystem: ZOTAC International (MCO) Ltd. Device 1366
Kernel driver in use: nvidiaclaims the nvidia module to be in use by the GPU
The Xorg.conf is the standard cruft, remove that and don't recreate it - at best it does nothing.
We're missing the xorg log and you can add your complete system journal for the boot:
sudo journalctl -b | curl -F 'file=@-' 0x0.st to that because of the contradiction between dkms and lspci.
(Did you maybe remove the driver but there's a copy in the initramfs?)
Offline
#5 2026-01-10 22:04:53
- drudox
- Member
- Registered: 2017-10-01
- Posts: 143
Re: X failure with nvidia-590 and nvidia gtx970
I removed xorg.conf (the issues is that i use 3 screen) and now just one is on ... (arandr doesn't see the other two)
this is Xorg.0.log:
[ 9.318]
X.Org X Server 1.21.1.21
X Protocol Version 11, Revision 0
[ 9.318] Current Operating System: Linux Arch7820X 6.12.64-1-lts #1 SMP PREEMPT_DYNAMIC Thu, 08 Jan 2026 11:19:30 +0000 x86_64
[ 9.318] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux-lts root=UUID=d2b24f37-26ee-493d-821a-882cc0909b16 rw quiet DEEPIN_GFXMODE=
[ 9.318]
[ 9.318] Current version of pixman: 0.46.4
[ 9.318] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 9.318] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 9.318] (==) Log file: "/var/log/Xorg.0.log", Time: Sat Jan 10 22:56:06 2026
[ 9.318] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 9.318] (==) No Layout section. Using the first Screen section.
[ 9.318] (==) No screen section available. Using defaults.
[ 9.318] (**) |-->Screen "Default Screen Section" (0)
[ 9.318] (**) | |-->Monitor "<default monitor>"
[ 9.318] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 9.318] (**) Allowing byte-swapped clients
[ 9.318] (==) Automatically adding devices
[ 9.318] (==) Automatically enabling devices
[ 9.318] (==) Automatically adding GPU devices
[ 9.318] (==) Automatically binding GPU devices
[ 9.318] (==) Max clients allowed: 256, resource mask: 0x1fffff
[ 9.318] (WW) The directory "/usr/share/fonts/Type1" does not exist.
[ 9.318] Entry deleted from font path.
[ 9.318] (==) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/TTF,
/usr/share/fonts/OTF,
/usr/share/fonts/100dpi,
/usr/share/fonts/75dpi
[ 9.318] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 9.318] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 9.318] (II) Module ABI versions:
[ 9.318] X.Org ANSI C Emulation: 0.4
[ 9.318] X.Org Video Driver: 25.2
[ 9.318] X.Org XInput driver : 24.4
[ 9.318] X.Org Server Extension : 10.0
[ 9.319] (++) using VT number 1
[ 9.319] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[ 9.321] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 9.321] (II) Platform probe for /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/simple-framebuffer.0/drm/card0
[ 9.325] (II) xfree86: Adding drm device (/dev/dri/card1)
[ 9.325] (II) Platform probe for /sys/devices/pci0000:00/0000:00:02.0/drm/card1
[ 9.328] (--) PCI: (0@0:2:0) 8086:a780:1462:7e29 rev 4, Mem @ 0x6012000000/16777216, 0x4000000000/268435456, I/O @ 0x00005000/64
[ 9.328] (--) PCI:*(1@0:0:0) 10de:13c2:19da:1366 rev 161, Mem @ 0x81000000/16777216, 0x6000000000/268435456, 0x6010000000/33554432, I/O @ 0x00004000/128, BIOS @ 0x????????/524288
[ 9.328] (II) LoadModule: "glx"
[ 9.328] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 9.329] (II) Module glx: vendor="X.Org Foundation"
[ 9.329] compiled for 1.21.1.21, module version = 1.0.0
[ 9.329] ABI class: X.Org Server Extension, version 10.0
[ 9.329] (==) Matched nouveau as autoconfigured driver 0
[ 9.329] (==) Matched nv as autoconfigured driver 1
[ 9.329] (==) Matched intel as autoconfigured driver 2
[ 9.329] (==) Matched modesetting as autoconfigured driver 3
[ 9.329] (==) Matched fbdev as autoconfigured driver 4
[ 9.329] (==) Matched vesa as autoconfigured driver 5
[ 9.329] (==) Assigned the driver to the xf86ConfigLayout
[ 9.329] (II) LoadModule: "nouveau"
[ 9.329] (WW) Warning, couldn't open module nouveau
[ 9.329] (EE) Failed to load module "nouveau" (module does not exist, 0)
[ 9.329] (II) LoadModule: "nv"
[ 9.329] (WW) Warning, couldn't open module nv
[ 9.329] (EE) Failed to load module "nv" (module does not exist, 0)
[ 9.329] (II) LoadModule: "intel"
[ 9.329] (WW) Warning, couldn't open module intel
[ 9.329] (EE) Failed to load module "intel" (module does not exist, 0)
[ 9.329] (II) LoadModule: "modesetting"
[ 9.329] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[ 9.329] (II) Module modesetting: vendor="X.Org Foundation"
[ 9.329] compiled for 1.21.1.21, module version = 1.21.1
[ 9.329] Module class: X.Org Video Driver
[ 9.329] ABI class: X.Org Video Driver, version 25.2
[ 9.329] (II) LoadModule: "fbdev"
[ 9.330] (WW) Warning, couldn't open module fbdev
[ 9.330] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 9.330] (II) LoadModule: "vesa"
[ 9.330] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[ 9.330] (II) Module vesa: vendor="X.Org Foundation"
[ 9.330] compiled for 1.21.1.11, module version = 2.6.0
[ 9.330] Module class: X.Org Video Driver
[ 9.330] ABI class: X.Org Video Driver, version 25.2
[ 9.330] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[ 9.330] (II) VESA: driver for VESA chipsets: vesa
[ 9.333] (II) modeset(0): using drv /dev/dri/card0
[ 9.333] (II) modeset(G0): using drv /dev/dri/card1
[ 9.333] (II) modeset(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 9.333] (==) modeset(0): Depth 24, (==) framebuffer bpp 32
[ 9.333] (==) modeset(0): RGB weight 888
[ 9.333] (==) modeset(0): Default visual is TrueColor
[ 9.333] (II) Loading sub module "glamoregl"
[ 9.333] (II) LoadModule: "glamoregl"
[ 9.333] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[ 9.336] (II) Module glamoregl: vendor="X.Org Foundation"
[ 9.336] compiled for 1.21.1.21, module version = 1.0.1
[ 9.336] ABI class: X.Org ANSI C Emulation, version 0.4
[ 9.367] (II) modeset(0): glamor: Using OpenGL 4.5 context.
[ 9.367] (II) modeset(0): Refusing to try glamor on llvmpipe
[ 9.368] (II) modeset(0): glamor initialization failed
[ 9.368] (II) modeset(0): ShadowFB: preferred NO, enabled NO
[ 9.368] (II) modeset(0): Output None-1 has no monitor section
[ 9.369] (II) modeset(0): EDID for output None-1
[ 9.369] (II) modeset(0): Printing probed modes for output None-1
[ 9.369] (II) modeset(0): Modeline "1920x1080"x60.0 124.42 1920 1920 1920 1920 1080 1080 1080 1080 (64.8 kHz eP)
[ 9.369] (II) modeset(0): Output None-1 connected
[ 9.369] (II) modeset(0): Using exact sizes for initial modes
[ 9.369] (II) modeset(0): Output None-1 using initial mode 1920x1080 +0+0
[ 9.369] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)
[ 9.369] (==) modeset(0): DPI set to (96, 96)
[ 9.369] (II) Loading sub module "fb"
[ 9.369] (II) LoadModule: "fb"
[ 9.369] (II) Module "fb" already built-in
[ 9.369] (==) modeset(G0): Depth 24, (==) framebuffer bpp 32
[ 9.369] (==) modeset(G0): RGB weight 888
[ 9.369] (==) modeset(G0): Default visual is TrueColor
[ 9.369] (II) Loading sub module "glamoregl"
[ 9.369] (II) LoadModule: "glamoregl"
[ 9.369] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[ 9.369] (II) Module glamoregl: vendor="X.Org Foundation"
[ 9.369] compiled for 1.21.1.21, module version = 1.0.1
[ 9.369] ABI class: X.Org ANSI C Emulation, version 0.4
[ 9.372] (II) modeset(G0): glamor: Using OpenGL 4.6 context.
[ 9.372] (II) modeset(G0): glamor X acceleration enabled on Mesa Intel(R) Graphics (RPL-S)
[ 9.372] (II) modeset(G0): glamor initialized
[ 9.380] (II) modeset(G0): Output HDMI-1-1 has no monitor section
[ 9.390] (II) modeset(G0): Output HDMI-1-2 has no monitor section
[ 9.400] (II) modeset(G0): Output DP-1-1 has no monitor section
[ 9.410] (II) modeset(G0): Output HDMI-1-3 has no monitor section
[ 9.420] (II) modeset(G0): Output DP-1-2 has no monitor section
[ 9.430] (II) modeset(G0): Output HDMI-1-4 has no monitor section
[ 9.440] (II) modeset(G0): EDID for output HDMI-1-1
[ 9.450] (II) modeset(G0): EDID for output HDMI-1-2
[ 9.460] (II) modeset(G0): EDID for output DP-1-1
[ 9.470] (II) modeset(G0): EDID for output HDMI-1-3
[ 9.480] (II) modeset(G0): EDID for output DP-1-2
[ 9.490] (II) modeset(G0): EDID for output HDMI-1-4
[ 9.490] (==) modeset(G0): Using gamma correction (1.0, 1.0, 1.0)
[ 9.490] (==) modeset(G0): DPI set to (96, 96)
[ 9.490] (II) Loading sub module "fb"
[ 9.490] (II) LoadModule: "fb"
[ 9.490] (II) Module "fb" already built-in
[ 9.490] (II) UnloadModule: "vesa"
[ 9.490] (II) Unloading vesa
[ 9.490] (==) modeset(0): Backing store enabled
[ 9.490] (==) modeset(0): Silken mouse enabled
[ 9.490] (II) modeset(0): Initializing kms color map for depth 24, 8 bpc.
[ 9.490] (==) modeset(0): DPMS enabled
[ 9.501] (==) modeset(G0): Backing store enabled
[ 9.501] (==) modeset(G0): Silken mouse enabled
[ 9.501] (II) modeset(G0): Initializing kms color map for depth 24, 8 bpc.
[ 9.501] (==) modeset(G0): DPMS enabled
[ 9.501] (II) modeset(G0): [DRI2] Setup complete
[ 9.501] (II) modeset(G0): [DRI2] DRI driver: iris
[ 9.501] (II) modeset(G0): [DRI2] VDPAU driver: va_gl
[ 9.501] (II) modeset(G0): Disable reverse prime offload mode for i915.
[ 9.501] (II) Initializing extension Generic Event Extension
[ 9.501] (II) Initializing extension SHAPE
[ 9.501] (II) Initializing extension MIT-SHM
[ 9.501] (II) Initializing extension XInputExtension
[ 9.502] (II) Initializing extension XTEST
[ 9.502] (II) Initializing extension BIG-REQUESTS
[ 9.502] (II) Initializing extension SYNC
[ 9.502] (II) Initializing extension XKEYBOARD
[ 9.502] (II) Initializing extension XC-MISC
[ 9.502] (II) Initializing extension SECURITY
[ 9.502] (II) Initializing extension XFIXES
[ 9.502] (II) Initializing extension RENDER
[ 9.502] (II) Initializing extension RANDR
[ 9.502] (II) Initializing extension COMPOSITE
[ 9.502] (II) Initializing extension DAMAGE
[ 9.502] (II) Initializing extension MIT-SCREEN-SAVER
[ 9.502] (II) Initializing extension DOUBLE-BUFFER
[ 9.502] (II) Initializing extension RECORD
[ 9.502] (II) Initializing extension DPMS
[ 9.502] (II) Initializing extension Present
[ 9.502] (II) Initializing extension DRI3
[ 9.502] (II) Initializing extension X-Resource
[ 9.502] (II) Initializing extension XVideo
[ 9.502] (II) Initializing extension XVideo-MotionCompensation
[ 9.502] (II) Initializing extension GLX
[ 9.502] (II) AIGLX: Screen 0 is not DRI2 capable
[ 9.508] (II) IGLX: Loaded and initialized swrast
[ 9.508] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[ 9.508] (II) Initializing extension XFree86-VidModeExtension
[ 9.508] (II) Initializing extension XFree86-DGA
[ 9.508] (II) Initializing extension XFree86-DRI
[ 9.508] (II) Initializing extension DRI2
[ 9.508] (II) modeset(G0): Damage tracking initialized
[ 9.509] (II) modeset(0): Damage tracking initialized
[ 9.509] (II) modeset(0): Setting screen physical size to 508 x 285
[ 9.544] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 9.544] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[ 9.544] (II) LoadModule: "libinput"
[ 9.544] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[ 9.545] (II) Module libinput: vendor="X.Org Foundation"
[ 9.545] compiled for 1.21.1.13, module version = 1.5.0
[ 9.545] Module class: X.Org XInput Driver
[ 9.545] ABI class: X.Org XInput driver, version 24.4
[ 9.545] (II) Using input driver 'libinput' for 'Power Button'
[ 9.545] (**) Power Button: always reports core events
[ 9.545] (**) Option "Device" "/dev/input/event2"
[ 9.545] (II) event2 - Power Button: is tagged by udev as: Keyboard
[ 9.545] (II) event2 - Power Button: device is a keyboard
[ 9.545] (II) event2 - Power Button: device removed
[ 9.586] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[ 9.586] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 9.588] (II) event2 - Power Button: is tagged by udev as: Keyboard
[ 9.588] (II) event2 - Power Button: device is a keyboard
[ 9.589] (II) config/udev: Adding input device Video Bus (/dev/input/event3)
[ 9.589] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[ 9.589] (II) Using input driver 'libinput' for 'Video Bus'
[ 9.589] (**) Video Bus: always reports core events
[ 9.589] (**) Option "Device" "/dev/input/event3"
[ 9.591] (II) event3 - Video Bus: is tagged by udev as: Keyboard
[ 9.591] (II) event3 - Video Bus: device is a keyboard
[ 9.591] (II) event3 - Video Bus: device removed
[ 9.653] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3/event3"
[ 9.653] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 9.655] (II) event3 - Video Bus: is tagged by udev as: Keyboard
[ 9.655] (II) event3 - Video Bus: device is a keyboard
[ 9.656] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 9.656] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[ 9.656] (II) Using input driver 'libinput' for 'Power Button'
[ 9.656] (**) Power Button: always reports core events
[ 9.656] (**) Option "Device" "/dev/input/event1"
[ 9.657] (II) event1 - Power Button: is tagged by udev as: Keyboard
[ 9.657] (II) event1 - Power Button: device is a keyboard
[ 9.657] (II) event1 - Power Button: device removed
[ 9.716] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1/event1"
[ 9.716] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[ 9.718] (II) event1 - Power Button: is tagged by udev as: Keyboard
[ 9.718] (II) event1 - Power Button: device is a keyboard
[ 9.719] (II) config/udev: Adding input device Sleep Button (/dev/input/event0)
[ 9.719] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"
[ 9.719] (II) Using input driver 'libinput' for 'Sleep Button'
[ 9.719] (**) Sleep Button: always reports core events
[ 9.719] (**) Option "Device" "/dev/input/event0"
[ 9.720] (II) event0 - Sleep Button: is tagged by udev as: Keyboard
[ 9.720] (II) event0 - Sleep Button: device is a keyboard
[ 9.721] (II) event0 - Sleep Button: device removed
[ 9.750] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0/event0"
[ 9.750] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[ 9.751] (II) event0 - Sleep Button: is tagged by udev as: Keyboard
[ 9.751] (II) event0 - Sleep Button: device is a keyboard
[ 9.753] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event10)
[ 9.753] (II) No input driver specified, ignoring this device.
[ 9.753] (II) This device may have been added with another device file.
[ 9.753] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event11)
[ 9.753] (II) No input driver specified, ignoring this device.
[ 9.753] (II) This device may have been added with another device file.
[ 9.754] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=8 (/dev/input/event12)
[ 9.754] (II) No input driver specified, ignoring this device.
[ 9.754] (II) This device may have been added with another device file.
[ 9.755] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=9 (/dev/input/event13)
[ 9.755] (II) No input driver specified, ignoring this device.
[ 9.755] (II) This device may have been added with another device file.
[ 9.757] (II) config/udev: Adding input device Dell KB216 Wired Keyboard (/dev/input/event4)
[ 9.757] (**) Dell KB216 Wired Keyboard: Applying InputClass "libinput keyboard catchall"
[ 9.757] (II) Using input driver 'libinput' for 'Dell KB216 Wired Keyboard'
[ 9.757] (**) Dell KB216 Wired Keyboard: always reports core events
[ 9.757] (**) Option "Device" "/dev/input/event4"
[ 9.759] (II) event4 - Dell KB216 Wired Keyboard: is tagged by udev as: Keyboard
[ 9.759] (II) event4 - Dell KB216 Wired Keyboard: device is a keyboard
[ 9.760] (II) event4 - Dell KB216 Wired Keyboard: device removed
[ 9.793] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-10/1-10:1.0/0003:413C:2113.0001/input/input4/event4"
[ 9.793] (II) XINPUT: Adding extended input device "Dell KB216 Wired Keyboard" (type: KEYBOARD, id 10)
[ 9.796] (II) event4 - Dell KB216 Wired Keyboard: is tagged by udev as: Keyboard
[ 9.796] (II) event4 - Dell KB216 Wired Keyboard: device is a keyboard
[ 9.797] (II) config/udev: Adding input device Dell KB216 Wired Keyboard System Control (/dev/input/event5)
[ 9.797] (**) Dell KB216 Wired Keyboard System Control: Applying InputClass "libinput keyboard catchall"
[ 9.797] (II) Using input driver 'libinput' for 'Dell KB216 Wired Keyboard System Control'
[ 9.797] (**) Dell KB216 Wired Keyboard System Control: always reports core events
[ 9.797] (**) Option "Device" "/dev/input/event5"
[ 9.799] (II) event5 - Dell KB216 Wired Keyboard System Control: is tagged by udev as: Keyboard
[ 9.800] (II) event5 - Dell KB216 Wired Keyboard System Control: device is a keyboard
[ 9.800] (II) event5 - Dell KB216 Wired Keyboard System Control: device removed
[ 9.853] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-10/1-10:1.1/0003:413C:2113.0002/input/input5/event5"
[ 9.853] (II) XINPUT: Adding extended input device "Dell KB216 Wired Keyboard System Control" (type: KEYBOARD, id 11)
[ 9.856] (II) event5 - Dell KB216 Wired Keyboard System Control: is tagged by udev as: Keyboard
[ 9.856] (II) event5 - Dell KB216 Wired Keyboard System Control: device is a keyboard
[ 9.857] (II) config/udev: Adding input device Dell KB216 Wired Keyboard Consumer Control (/dev/input/event6)
[ 9.857] (**) Dell KB216 Wired Keyboard Consumer Control: Applying InputClass "libinput keyboard catchall"
[ 9.857] (II) Using input driver 'libinput' for 'Dell KB216 Wired Keyboard Consumer Control'
[ 9.857] (**) Dell KB216 Wired Keyboard Consumer Control: always reports core events
[ 9.857] (**) Option "Device" "/dev/input/event6"
[ 9.859] (II) event6 - Dell KB216 Wired Keyboard Consumer Control: is tagged by udev as: Keyboard
[ 9.860] (II) event6 - Dell KB216 Wired Keyboard Consumer Control: device is a keyboard
[ 9.860] (II) event6 - Dell KB216 Wired Keyboard Consumer Control: device removed
[ 9.893] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-10/1-10:1.1/0003:413C:2113.0002/input/input6/event6"
[ 9.893] (II) XINPUT: Adding extended input device "Dell KB216 Wired Keyboard Consumer Control" (type: KEYBOARD, id 12)
[ 9.896] (II) event6 - Dell KB216 Wired Keyboard Consumer Control: is tagged by udev as: Keyboard
[ 9.896] (II) event6 - Dell KB216 Wired Keyboard Consumer Control: device is a keyboard
[ 9.897] (II) config/udev: Adding input device MSI MYSTIC LIGHT (/dev/input/event8)
[ 9.897] (II) No input driver specified, ignoring this device.
[ 9.897] (II) This device may have been added with another device file.
[ 9.899] (II) config/udev: Adding input device PixArt HP 1000 USB Optical Mouse (/dev/input/event7)
[ 9.899] (**) PixArt HP 1000 USB Optical Mouse: Applying InputClass "libinput pointer catchall"
[ 9.899] (II) Using input driver 'libinput' for 'PixArt HP 1000 USB Optical Mouse'
[ 9.899] (**) PixArt HP 1000 USB Optical Mouse: always reports core events
[ 9.899] (**) Option "Device" "/dev/input/event7"
[ 9.901] (II) event7 - PixArt HP 1000 USB Optical Mouse: is tagged by udev as: Mouse
[ 9.901] (II) event7 - PixArt HP 1000 USB Optical Mouse: device is a pointer
[ 9.902] (II) event7 - PixArt HP 1000 USB Optical Mouse: device removed
[ 9.940] (II) libinput: PixArt HP 1000 USB Optical Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 9.940] (II) libinput: PixArt HP 1000 USB Optical Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 9.940] (II) libinput: PixArt HP 1000 USB Optical Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 9.940] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-9/1-9.3/1-9.3:1.0/0003:03F0:2A41.0003/input/input7/event7"
[ 9.940] (II) XINPUT: Adding extended input device "PixArt HP 1000 USB Optical Mouse" (type: MOUSE, id 13)
[ 9.940] (**) Option "AccelerationScheme" "none"
[ 9.940] (**) PixArt HP 1000 USB Optical Mouse: (accel) selected scheme none/0
[ 9.940] (**) PixArt HP 1000 USB Optical Mouse: (accel) acceleration factor: 2.000
[ 9.940] (**) PixArt HP 1000 USB Optical Mouse: (accel) acceleration threshold: 4
[ 9.943] (II) event7 - PixArt HP 1000 USB Optical Mouse: is tagged by udev as: Mouse
[ 9.943] (II) event7 - PixArt HP 1000 USB Optical Mouse: device is a pointer
[ 9.945] (II) config/udev: Adding input device PixArt HP 1000 USB Optical Mouse (/dev/input/mouse0)
[ 9.945] (II) No input driver specified, ignoring this device.
[ 9.945] (II) This device may have been added with another device file.
[ 9.945] (II) config/udev: Adding input device HDA Intel PCH Rear Mic (/dev/input/event14)
[ 9.945] (II) No input driver specified, ignoring this device.
[ 9.945] (II) This device may have been added with another device file.
[ 9.946] (II) config/udev: Adding input device HDA Intel PCH Front Mic (/dev/input/event15)
[ 9.946] (II) No input driver specified, ignoring this device.
[ 9.946] (II) This device may have been added with another device file.
[ 9.947] (II) config/udev: Adding input device HDA Intel PCH Line (/dev/input/event16)
[ 9.947] (II) No input driver specified, ignoring this device.
[ 9.947] (II) This device may have been added with another device file.
[ 9.947] (II) config/udev: Adding input device HDA Intel PCH Line Out Front (/dev/input/event17)
[ 9.948] (II) No input driver specified, ignoring this device.
[ 9.948] (II) This device may have been added with another device file.
[ 9.948] (II) config/udev: Adding input device HDA Intel PCH Line Out Surround (/dev/input/event18)
[ 9.948] (II) No input driver specified, ignoring this device.
[ 9.948] (II) This device may have been added with another device file.
[ 9.949] (II) config/udev: Adding input device HDA Intel PCH Line Out CLFE (/dev/input/event19)
[ 9.949] (II) No input driver specified, ignoring this device.
[ 9.949] (II) This device may have been added with another device file.
[ 9.950] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event20)
[ 9.950] (II) No input driver specified, ignoring this device.
[ 9.950] (II) This device may have been added with another device file.
[ 9.950] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=3 (/dev/input/event21)
[ 9.950] (II) No input driver specified, ignoring this device.
[ 9.950] (II) This device may have been added with another device file.
[ 9.951] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=7 (/dev/input/event22)
[ 9.951] (II) No input driver specified, ignoring this device.
[ 9.951] (II) This device may have been added with another device file.
[ 9.952] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=8 (/dev/input/event23)
[ 9.952] (II) No input driver specified, ignoring this device.
[ 9.952] (II) This device may have been added with another device file.
[ 9.952] (II) config/udev: Adding input device HDA Intel PCH HDMI/DP,pcm=9 (/dev/input/event24)
[ 9.952] (II) No input driver specified, ignoring this device.
[ 9.952] (II) This device may have been added with another device file.
[ 9.953] (II) config/udev: Adding input device PC Speaker (/dev/input/event9)
[ 9.953] (II) No input driver specified, ignoring this device.
[ 9.953] (II) This device may have been added with another device file.and the last journalctb:
http://0x0.st/PXmg.txt
Offline
#6 2026-01-10 22:13:00
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 72,057
Re: X failure with nvidia-590 and nvidia gtx970
It's a hybrid graphics system, the nvidia driver isn't being used, modesetting runs the intel chip and the simpledrm device (in lieu of the nvidia driver)
There's also no way that this system produces the output
Kernel driver in use: nvidiaanywere.
You're likely lacking linux-lts-headers?
Rebuild the nvidia-580xx-dkms module and post the build log.
Edit: read https://wiki.archlinux.org/title/Dynami … le_Support
Last edited by seth (2026-01-10 22:13:16)
Offline
#7 2026-01-10 22:34:46
- drudox
- Member
- Registered: 2017-10-01
- Posts: 143
Re: X failure with nvidia-590 and nvidia gtx970
phobos@Arch7820X ~ yay -S nvidia-580xx-dkms
AUR Explicit (1): nvidia-580xx-dkms-580.119.02-2
Sync Make Dependency (1): patchelf-0.18.0-4
:: (1/1) Downloaded PKGBUILD: nvidia-580xx-utils
1 nvidia-580xx-utils (Installed) (Build Files Exist)
==> Packages to cleanBuild?
==> [N]one [A]ll [Ab]ort [I]nstalled [No]tInstalled or (1 2 3, 1-3, ^4)
==>
1 nvidia-580xx-utils (Installed) (Build Files Exist)
==> Diffs to show?
==> [N]one [A]ll [Ab]ort [I]nstalled [No]tInstalled or (1 2 3, 1-3, ^4)
==>
==> Making package: nvidia-580xx-utils 580.119.02-2 (Sat 10 Jan 2026 23:29:44 CET)
==> Retrieving sources...
-> Found nvidia-drm-outputclass.conf
-> Found nvidia-utils.sysusers
-> Found nvidia.rules
-> Found systemd-homed-override.conf
-> Found systemd-suspend-override.conf
-> Found nvidia-sleep.conf
-> Downloading NVIDIA-Linux-x86_64-580.119.02.run...
% Total % Received % Xferd Average Speed Time Time Time Current
Dload Upload Total Spent Left Speed
100 379.3M 100 379.3M 0 0 3.50M 0 01:48 01:48 3.14M
-> Found 0001-Enable-atomic-kernel-modesetting-by-default.patch
-> Found limit-vram-usage
==> WARNING: Skipping verification of source file PGP signatures.
==> Validating source files with sha256sums...
nvidia-drm-outputclass.conf ... Passed
nvidia-utils.sysusers ... Passed
nvidia.rules ... Passed
systemd-homed-override.conf ... Passed
systemd-suspend-override.conf ... Passed
nvidia-sleep.conf ... Passed
NVIDIA-Linux-x86_64-580.119.02.run ... Passed
0001-Enable-atomic-kernel-modesetting-by-default.patch ... Passed
limit-vram-usage ... Passed
:: Remove make dependencies after install? [y/N] y
:: (1/1) Parsing SRCINFO: nvidia-580xx-utils
[sudo] password for phobos:
resolving dependencies...
looking for conflicting packages...
Packages (1) patchelf-0.18.0-4
Total Installed Size: 0.26 MiB
:: Proceed with installation? [Y/n]
(1/1) checking keys in keyring [#################################] 100%
(1/1) checking package integrity [#################################] 100%
(1/1) loading package files [#################################] 100%
(1/1) checking for file conflicts [#################################] 100%
(1/1) checking available disk space [#################################] 100%
:: Processing package changes...
(1/1) installing patchelf [#################################] 100%
:: Running post-transaction hooks...
(1/1) Arming ConditionNeedsUpdate...
==> Making package: nvidia-580xx-utils 580.119.02-2 (Sat 10 Jan 2026 23:31:54 CET)
==> Checking runtime dependencies...
==> Checking buildtime dependencies...
==> Retrieving sources...
-> Found nvidia-drm-outputclass.conf
-> Found nvidia-utils.sysusers
-> Found nvidia.rules
-> Found systemd-homed-override.conf
-> Found systemd-suspend-override.conf
-> Found nvidia-sleep.conf
-> Found NVIDIA-Linux-x86_64-580.119.02.run
-> Found 0001-Enable-atomic-kernel-modesetting-by-default.patch
-> Found limit-vram-usage
==> Validating source files with sha256sums...
nvidia-drm-outputclass.conf ... Passed
nvidia-utils.sysusers ... Passed
nvidia.rules ... Passed
systemd-homed-override.conf ... Passed
systemd-suspend-override.conf ... Passed
nvidia-sleep.conf ... Passed
NVIDIA-Linux-x86_64-580.119.02.run ... Passed
0001-Enable-atomic-kernel-modesetting-by-default.patch ... Passed
limit-vram-usage ... Passed
==> Removing existing $srcdir/ directory...
==> Extracting sources...
==> Starting prepare()...
Creating directory NVIDIA-Linux-x86_64-580.119.02
Verifying archive integrity... OK
Uncompressing NVIDIA Accelerated Graphics Driver for Linux-x86_64 580.119.02....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
patching file nvidia-drm/nvidia-drm-linux.c
patching file nvidia-drm/nvidia-drm-os-interface.c
Hunk #1 succeeded at 38 (offset -3 lines).
==> Sources are ready.
==> Making package: nvidia-580xx-utils 580.119.02-2 (Sat 10 Jan 2026 23:32:08 CET)
==> Checking runtime dependencies...
==> Checking buildtime dependencies...
==> WARNING: Using existing $srcdir/ tree
==> Entering fakeroot environment...
==> Starting package_nvidia-580xx-utils()...
libnvidia-pkcs11-openssl3.so.580.119.02 libnvidia-pkcs11.so.580.119.02
libnvidia-pkcs11-openssl3.so.580.119.02
==> Tidying install...
-> Removing libtool files...
-> Purging unreproducible ruby files...
-> Removing static library files...
-> Purging unwanted files...
-> Copying source files needed for debug symbols...
-> Compressing man and info pages...
==> Checking for packaging issues...
==> Creating package "nvidia-580xx-utils"...
-> Generating .PKGINFO file...
-> Generating .BUILDINFO file...
-> Adding install file...
-> Generating .MTREE file...
-> Compressing package...
==> Starting package_opencl-nvidia-580xx()...
==> Tidying install...
-> Removing libtool files...
-> Purging unreproducible ruby files...
-> Removing static library files...
-> Purging unwanted files...
-> Copying source files needed for debug symbols...
-> Compressing man and info pages...
==> Checking for packaging issues...
==> Creating package "opencl-nvidia-580xx"...
-> Generating .PKGINFO file...
-> Generating .BUILDINFO file...
-> Generating .MTREE file...
-> Compressing package...
==> Starting package_nvidia-580xx-dkms()...
==> Tidying install...
-> Removing libtool files...
-> Purging unreproducible ruby files...
-> Removing static library files...
-> Purging unwanted files...
-> Copying source files needed for debug symbols...
-> Compressing man and info pages...
==> Checking for packaging issues...
==> Creating package "nvidia-580xx-dkms"...
-> Generating .PKGINFO file...
-> Generating .BUILDINFO file...
-> Generating .MTREE file...
-> Compressing package...
==> Leaving fakeroot environment.
==> Finished making: nvidia-580xx-utils 580.119.02-2 (Sat 10 Jan 2026 23:32:24 CET)
==> Cleaning up...
loading packages...
warning: nvidia-580xx-dkms-580.119.02-2 is up to date -- reinstalling
resolving dependencies...
looking for conflicting packages...
Packages (1) nvidia-580xx-dkms-580.119.02-2
Total Installed Size: 117.83 MiB
Net Upgrade Size: 0.00 MiB
:: Proceed with installation? [Y/n]
(1/1) checking keys in keyring [#################################] 100%
(1/1) checking package integrity [#################################] 100%
(1/1) loading package files [#################################] 100%
(1/1) checking for file conflicts [#################################] 100%
(1/1) checking available disk space [#################################] 100%
:: Running pre-transaction hooks...
(1/1) Remove upgraded DKMS modules
:: Processing package changes...
(1/1) reinstalling nvidia-580xx-dkms [#################################] 100%
:: Running post-transaction hooks...
(1/3) Arming ConditionNeedsUpdate...
(2/3) Install DKMS modules
==> ERROR: Missing part.txt kernel headers for module nvidia/580.119.02.
==> ERROR: Missing sys kernel headers for module nvidia/580.119.02.
==> ERROR: Missing etc kernel headers for module nvidia/580.119.02.
==> ERROR: Missing mnt3 kernel headers for module nvidia/580.119.02.
==> ERROR: Missing mnt2 kernel headers for module nvidia/580.119.02.
==> ERROR: Missing cmd.txt kernel headers for module nvidia/580.119.02.
==> ERROR: Missing tmp kernel headers for module nvidia/580.119.02.
==> ERROR: Missing yay kernel headers for module nvidia/580.119.02.
==> ERROR: Missing home kernel headers for module nvidia/580.119.02.
==> ERROR: Missing boot kernel headers for module nvidia/580.119.02.
==> ERROR: Missing mnt kernel headers for module nvidia/580.119.02.
==> ERROR: Missing part2.txt kernel headers for module nvidia/580.119.02.
==> ERROR: Missing proc kernel headers for module nvidia/580.119.02.
==> ERROR: Missing media kernel headers for module nvidia/580.119.02.
==> ERROR: Missing tool_efi kernel headers for module nvidia/580.119.02.
==> ERROR: Missing run kernel headers for module nvidia/580.119.02.
==> ERROR: Missing lib kernel headers for module nvidia/580.119.02.
==> ERROR: Missing root kernel headers for module nvidia/580.119.02.
==> ERROR: Missing dev kernel headers for module nvidia/580.119.02.
==> ERROR: Missing sbin kernel headers for module nvidia/580.119.02.
==> ERROR: Missing opt kernel headers for module nvidia/580.119.02.
==> ERROR: Missing srv kernel headers for module nvidia/580.119.02.
==> ERROR: Missing lost+found kernel headers for module nvidia/580.119.02.
==> ERROR: Missing lib64 kernel headers for module nvidia/580.119.02.
==> ERROR: Missing bin kernel headers for module nvidia/580.119.02.
==> ERROR: Missing usr kernel headers for module nvidia/580.119.02.
==> ERROR: Missing hostlvm kernel headers for module nvidia/580.119.02.
==> ERROR: Missing grub2-sh-Jof39p kernel headers for module nvidia/580.119.02.
==> ERROR: Missing var kernel headers for module nvidia/580.119.02.
(3/3) Updating linux initcpios...
==> Building image from preset: /etc/mkinitcpio.d/linux-lts.preset: 'default'
==> Using default configuration file: '/etc/mkinitcpio.conf'
-> -k /boot/vmlinuz-linux-lts -g /boot/initramfs-linux-lts.img
==> Starting build: '6.12.64-1-lts'
-> Running build hook: [base]
-> Running build hook: [systemd]
-> Running build hook: [autodetect]
-> Running build hook: [microcode]
-> Running build hook: [modconf]
-> Running build hook: [kms]
-> Running build hook: [keyboard]
-> Running build hook: [keymap]
-> Running build hook: [sd-vconsole]
-> Running build hook: [block]
-> Running build hook: [filesystems]
-> Running build hook: [fsck]
==> Generating module dependencies
==> Creating zstd-compressed initcpio image: '/boot/initramfs-linux-lts.img'
-> Early uncompressed CPIO image generation successful
==> Initcpio image generation successful
==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'default'
==> Using default configuration file: '/etc/mkinitcpio.conf'
-> -k /boot/vmlinuz-linux -g /boot/initramfs-linux.img
==> Starting build: '6.18.4-arch1-1'
-> Running build hook: [base]
-> Running build hook: [systemd]
-> Running build hook: [autodetect]
-> Running build hook: [microcode]
-> Running build hook: [modconf]
-> Running build hook: [kms]
-> Running build hook: [keyboard]
-> Running build hook: [keymap]
-> Running build hook: [sd-vconsole]
-> Running build hook: [block]
-> Running build hook: [filesystems]
-> Running build hook: [fsck]
==> Generating module dependencies
==> Creating zstd-compressed initcpio image: '/boot/initramfs-linux.img'
-> Early uncompressed CPIO image generation successful
==> Initcpio image generation successful
checking dependencies...
Packages (1) patchelf-0.18.0-4
Total Removed Size: 0.26 MiB
:: Do you want to remove these packages? [Y/n]
:: Processing package changes...
(1/1) removing patchelf [#################################] 100%
:: Running post-transaction hooks...
(1/1) Arming ConditionNeedsUpdate...What a mess :\
Offline
#8 2026-01-10 22:35:21
- drudox
- Member
- Registered: 2017-10-01
- Posts: 143
Re: X failure with nvidia-590 and nvidia gtx970
I have both ... linux and linux-lts
Offline
#9 2026-01-10 22:37:53
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 72,057
Re: X failure with nvidia-590 and nvidia gtx970
And you're gonna need both header packages.
Though the LTS generation seems to have succeeded, so that kernel should now work?
Offline
#10 2026-01-10 22:39:54
- drudox
- Member
- Registered: 2017-10-01
- Posts: 143
Re: X failure with nvidia-590 and nvidia gtx970
sorry didn't got ! now I'm on lts
Offline
#11 2026-01-10 22:44:47
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 72,057
Re: X failure with nvidia-590 and nvidia gtx970
"dkms status", if it's says it's installed for linux-lts, reboot and in doubt post an updated Xorg log and journal
Offline
#12 2026-01-10 22:51:17
- drudox
- Member
- Registered: 2017-10-01
- Posts: 143
Re: X failure with nvidia-590 and nvidia gtx970
phobos@Arch7820X ~ dkms status
phobos@Arch7820X ~
still empty ...
xorg.0.log:
[ 9.858]
X.Org X Server 1.21.1.21
X Protocol Version 11, Revision 0
[ 9.858] Current Operating System: Linux Arch7820X 6.12.64-1-lts #1 SMP PREEMPT_DYNAMIC Thu, 08 Jan 2026 11:19:30 +0000 x86_64
[ 9.858] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux-lts root=UUID=d2b24f37-26ee-493d-821a-882cc0909b16 rw quiet DEEPIN_GFXMODE=
[ 9.858]
[ 9.858] Current version of pixman: 0.46.4
[ 9.858] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 9.858] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 9.858] (==) Log file: "/var/log/Xorg.0.log", Time: Sat Jan 10 23:48:21 2026
[ 9.858] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 9.859] (==) No Layout section. Using the first Screen section.
[ 9.859] (==) No screen section available. Using defaults.
[ 9.859] (**) |-->Screen "Default Screen Section" (0)
[ 9.859] (**) | |-->Monitor "<default monitor>"
[ 9.859] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 9.859] (**) Allowing byte-swapped clients
[ 9.859] (==) Automatically adding devices
[ 9.859] (==) Automatically enabling devices
[ 9.859] (==) Automatically adding GPU devices
[ 9.859] (==) Automatically binding GPU devices
[ 9.859] (==) Max clients allowed: 256, resource mask: 0x1fffff
[ 9.859] (WW) The directory "/usr/share/fonts/Type1" does not exist.
[ 9.859] Entry deleted from font path.
[ 9.859] (==) FontPath set to:
/usr/share/fonts/misc,
/usr/share/fonts/TTF,
/usr/share/fonts/OTF,
/usr/share/fonts/100dpi,
/usr/share/fonts/75dpi
[ 9.859] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 9.859] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 9.859] (II) Module ABI versions:
[ 9.859] X.Org ANSI C Emulation: 0.4
[ 9.859] X.Org Video Driver: 25.2
[ 9.859] X.Org XInput driver : 24.4
[ 9.859] X.Org Server Extension : 10.0
[ 9.859] (++) using VT number 1
[ 9.859] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[ 9.860] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 9.860] (II) Platform probe for /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/simple-framebuffer.0/drm/card0
[ 9.864] (--) PCI: (0@0:2:0) 8086:a780:1462:7e29 rev 4, Mem @ 0x6012000000/16777216, 0x4000000000/268435456, I/O @ 0x00005000/64
[ 9.864] (--) PCI:*(1@0:0:0) 10de:13c2:19da:1366 rev 161, Mem @ 0x81000000/16777216, 0x6000000000/268435456, 0x6010000000/33554432, I/O @ 0x00004000/128, BIOS @ 0x????????/524288
[ 9.864] (II) LoadModule: "glx"
[ 9.864] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 9.865] (II) Module glx: vendor="X.Org Foundation"
[ 9.865] compiled for 1.21.1.21, module version = 1.0.0
[ 9.865] ABI class: X.Org Server Extension, version 10.0
[ 9.865] (==) Matched nouveau as autoconfigured driver 0
[ 9.865] (==) Matched nv as autoconfigured driver 1
[ 9.865] (==) Matched modesetting as autoconfigured driver 2
[ 9.865] (==) Matched fbdev as autoconfigured driver 3
[ 9.865] (==) Matched vesa as autoconfigured driver 4
[ 9.865] (==) Assigned the driver to the xf86ConfigLayout
[ 9.865] (II) LoadModule: "nouveau"
[ 9.866] (WW) Warning, couldn't open module nouveau
[ 9.866] (EE) Failed to load module "nouveau" (module does not exist, 0)
[ 9.866] (II) LoadModule: "nv"
[ 9.866] (WW) Warning, couldn't open module nv
[ 9.866] (EE) Failed to load module "nv" (module does not exist, 0)
[ 9.866] (II) LoadModule: "modesetting"
[ 9.866] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[ 9.866] (II) Module modesetting: vendor="X.Org Foundation"
[ 9.866] compiled for 1.21.1.21, module version = 1.21.1
[ 9.866] Module class: X.Org Video Driver
[ 9.866] ABI class: X.Org Video Driver, version 25.2
[ 9.866] (II) LoadModule: "fbdev"
[ 9.866] (WW) Warning, couldn't open module fbdev
[ 9.866] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 9.866] (II) LoadModule: "vesa"
[ 9.866] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[ 9.866] (II) Module vesa: vendor="X.Org Foundation"
[ 9.866] compiled for 1.21.1.11, module version = 2.6.0
[ 9.866] Module class: X.Org Video Driver
[ 9.866] ABI class: X.Org Video Driver, version 25.2
[ 9.866] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[ 9.866] (II) VESA: driver for VESA chipsets: vesa
[ 9.869] (II) modeset(0): using drv /dev/dri/card0
[ 9.869] (II) modeset(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 9.869] (==) modeset(0): Depth 24, (==) framebuffer bpp 32
[ 9.869] (==) modeset(0): RGB weight 888
[ 9.869] (==) modeset(0): Default visual is TrueColor
[ 9.869] (II) Loading sub module "glamoregl"
[ 9.869] (II) LoadModule: "glamoregl"
[ 9.869] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[ 9.872] (II) Module glamoregl: vendor="X.Org Foundation"
[ 9.872] compiled for 1.21.1.21, module version = 1.0.1
[ 9.872] ABI class: X.Org ANSI C Emulation, version 0.4
[ 9.900] (II) modeset(0): glamor: Using OpenGL 4.5 context.
[ 9.900] (II) modeset(0): Refusing to try glamor on llvmpipe
[ 9.901] (II) modeset(0): glamor initialization failed
[ 9.901] (II) modeset(0): ShadowFB: preferred NO, enabled NO
[ 9.901] (II) modeset(0): Output None-1 has no monitor section
[ 9.901] (II) modeset(0): EDID for output None-1
[ 9.901] (II) modeset(0): Printing probed modes for output None-1
[ 9.901] (II) modeset(0): Modeline "1920x1080"x60.0 124.42 1920 1920 1920 1920 1080 1080 1080 1080 (64.8 kHz eP)
[ 9.901] (II) modeset(0): Output None-1 connected
[ 9.901] (II) modeset(0): Using exact sizes for initial modes
[ 9.901] (II) modeset(0): Output None-1 using initial mode 1920x1080 +0+0
[ 9.901] (==) modeset(0): Using gamma correction (1.0, 1.0, 1.0)
[ 9.901] (==) modeset(0): DPI set to (96, 96)
[ 9.901] (II) Loading sub module "fb"
[ 9.902] (II) LoadModule: "fb"
[ 9.902] (II) Module "fb" already built-in
[ 9.902] (II) UnloadModule: "vesa"
[ 9.902] (II) Unloading vesa
[ 9.902] (==) modeset(0): Backing store enabled
[ 9.902] (==) modeset(0): Silken mouse enabled
[ 9.902] (II) modeset(0): Initializing kms color map for depth 24, 8 bpc.
[ 9.902] (==) modeset(0): DPMS enabled
[ 9.902] (II) Initializing extension Generic Event Extension
[ 9.902] (II) Initializing extension SHAPE
[ 9.902] (II) Initializing extension MIT-SHM
[ 9.902] (II) Initializing extension XInputExtension
[ 9.902] (II) Initializing extension XTEST
[ 9.902] (II) Initializing extension BIG-REQUESTS
[ 9.902] (II) Initializing extension SYNC
[ 9.902] (II) Initializing extension XKEYBOARD
[ 9.902] (II) Initializing extension XC-MISC
[ 9.902] (II) Initializing extension SECURITY
[ 9.902] (II) Initializing extension XFIXES
[ 9.902] (II) Initializing extension RENDER
[ 9.902] (II) Initializing extension RANDR
[ 9.902] (II) Initializing extension COMPOSITE
[ 9.902] (II) Initializing extension DAMAGE
[ 9.902] (II) Initializing extension MIT-SCREEN-SAVER
[ 9.902] (II) Initializing extension DOUBLE-BUFFER
[ 9.902] (II) Initializing extension RECORD
[ 9.902] (II) Initializing extension DPMS
[ 9.902] (II) Initializing extension Present
[ 9.902] (II) Initializing extension DRI3
[ 9.902] (II) Initializing extension X-Resource
[ 9.903] (II) Initializing extension XVideo
[ 9.903] (II) Initializing extension XVideo-MotionCompensation
[ 9.903] (II) Initializing extension GLX
[ 9.903] (II) AIGLX: Screen 0 is not DRI2 capable
[ 9.906] (II) IGLX: Loaded and initialized swrast
[ 9.906] (II) GLX: Initialized DRISWRAST GL provider for screen 0
[ 9.906] (II) Initializing extension XFree86-VidModeExtension
[ 9.906] (II) Initializing extension XFree86-DGA
[ 9.906] (II) Initializing extension XFree86-DRI
[ 9.906] (II) Initializing extension DRI2
[ 9.907] (II) modeset(0): Damage tracking initialized
[ 9.907] (II) modeset(0): Setting screen physical size to 508 x 285
[ 9.941] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 9.941] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[ 9.941] (II) LoadModule: "libinput"
[ 9.941] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[ 9.941] (II) Module libinput: vendor="X.Org Foundation"
[ 9.942] compiled for 1.21.1.13, module version = 1.5.0
[ 9.942] Module class: X.Org XInput Driver
[ 9.942] ABI class: X.Org XInput driver, version 24.4
[ 9.942] (II) Using input driver 'libinput' for 'Power Button'
[ 9.942] (**) Power Button: always reports core events
[ 9.942] (**) Option "Device" "/dev/input/event2"
[ 9.942] (II) event2 - Power Button: is tagged by udev as: Keyboard
[ 9.942] (II) event2 - Power Button: device is a keyboard
[ 9.942] (II) event2 - Power Button: device removed
[ 9.990] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[ 9.990] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 9.991] (II) event2 - Power Button: is tagged by udev as: Keyboard
[ 9.991] (II) event2 - Power Button: device is a keyboard
[ 9.992] (II) config/udev: Adding input device Video Bus (/dev/input/event3)
[ 9.992] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[ 9.992] (II) Using input driver 'libinput' for 'Video Bus'
[ 9.992] (**) Video Bus: always reports core events
[ 9.992] (**) Option "Device" "/dev/input/event3"
[ 9.994] (II) event3 - Video Bus: is tagged by udev as: Keyboard
[ 9.994] (II) event3 - Video Bus: device is a keyboard
[ 9.994] (II) event3 - Video Bus: device removed
[ 10.023] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3/event3"
[ 10.023] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 10.025] (II) event3 - Video Bus: is tagged by udev as: Keyboard
[ 10.025] (II) event3 - Video Bus: device is a keyboard
[ 10.026] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 10.026] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[ 10.026] (II) Using input driver 'libinput' for 'Power Button'
[ 10.026] (**) Power Button: always reports core events
[ 10.026] (**) Option "Device" "/dev/input/event1"
[ 10.027] (II) event1 - Power Button: is tagged by udev as: Keyboard
[ 10.027] (II) event1 - Power Button: device is a keyboard
[ 10.027] (II) event1 - Power Button: device removed
[ 10.046] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1/event1"
[ 10.046] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[ 10.048] (II) event1 - Power Button: is tagged by udev as: Keyboard
[ 10.048] (II) event1 - Power Button: device is a keyboard
[ 10.049] (II) config/udev: Adding input device Sleep Button (/dev/input/event0)
[ 10.049] (**) Sleep Button: Applying InputClass "libinput keyboard catchall"
[ 10.049] (II) Using input driver 'libinput' for 'Sleep Button'
[ 10.049] (**) Sleep Button: always reports core events
[ 10.049] (**) Option "Device" "/dev/input/event0"
[ 10.050] (II) event0 - Sleep Button: is tagged by udev as: Keyboard
[ 10.050] (II) event0 - Sleep Button: device is a keyboard
[ 10.050] (II) event0 - Sleep Button: device removed
[ 10.076] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0/event0"
[ 10.076] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[ 10.078] (II) event0 - Sleep Button: is tagged by udev as: Keyboard
[ 10.078] (II) event0 - Sleep Button: device is a keyboard
[ 10.079] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event10)
[ 10.079] (II) No input driver specified, ignoring this device.
[ 10.079] (II) This device may have been added with another device file.
[ 10.080] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event11)
[ 10.080] (II) No input driver specified, ignoring this device.
[ 10.080] (II) This device may have been added with another device file.
[ 10.081] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=8 (/dev/input/event12)
[ 10.081] (II) No input driver specified, ignoring this device.
[ 10.081] (II) This device may have been added with another device file.
[ 10.082] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=9 (/dev/input/event13)
[ 10.082] (II) No input driver specified, ignoring this device.
[ 10.082] (II) This device may have been added with another device file.
[ 10.083] (II) config/udev: Adding input device Dell KB216 Wired Keyboard (/dev/input/event4)
[ 10.083] (**) Dell KB216 Wired Keyboard: Applying InputClass "libinput keyboard catchall"
[ 10.083] (II) Using input driver 'libinput' for 'Dell KB216 Wired Keyboard'
[ 10.083] (**) Dell KB216 Wired Keyboard: always reports core events
[ 10.083] (**) Option "Device" "/dev/input/event4"
[ 10.085] (II) event4 - Dell KB216 Wired Keyboard: is tagged by udev as: Keyboard
[ 10.085] (II) event4 - Dell KB216 Wired Keyboard: device is a keyboard
[ 10.086] (II) event4 - Dell KB216 Wired Keyboard: device removed
[ 10.106] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-10/1-10:1.0/0003:413C:2113.0001/input/input4/event4"
[ 10.106] (II) XINPUT: Adding extended input device "Dell KB216 Wired Keyboard" (type: KEYBOARD, id 10)
[ 10.109] (II) event4 - Dell KB216 Wired Keyboard: is tagged by udev as: Keyboard
[ 10.109] (II) event4 - Dell KB216 Wired Keyboard: device is a keyboard
[ 10.111] (II) config/udev: Adding input device Dell KB216 Wired Keyboard System Control (/dev/input/event5)
[ 10.111] (**) Dell KB216 Wired Keyboard System Control: Applying InputClass "libinput keyboard catchall"
[ 10.111] (II) Using input driver 'libinput' for 'Dell KB216 Wired Keyboard System Control'
[ 10.111] (**) Dell KB216 Wired Keyboard System Control: always reports core events
[ 10.111] (**) Option "Device" "/dev/input/event5"
[ 10.113] (II) event5 - Dell KB216 Wired Keyboard System Control: is tagged by udev as: Keyboard
[ 10.113] (II) event5 - Dell KB216 Wired Keyboard System Control: device is a keyboard
[ 10.113] (II) event5 - Dell KB216 Wired Keyboard System Control: device removed
[ 10.130] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-10/1-10:1.1/0003:413C:2113.0002/input/input5/event5"
[ 10.130] (II) XINPUT: Adding extended input device "Dell KB216 Wired Keyboard System Control" (type: KEYBOARD, id 11)
[ 10.132] (II) event5 - Dell KB216 Wired Keyboard System Control: is tagged by udev as: Keyboard
[ 10.132] (II) event5 - Dell KB216 Wired Keyboard System Control: device is a keyboard
[ 10.134] (II) config/udev: Adding input device Dell KB216 Wired Keyboard Consumer Control (/dev/input/event6)
[ 10.134] (**) Dell KB216 Wired Keyboard Consumer Control: Applying InputClass "libinput keyboard catchall"
[ 10.134] (II) Using input driver 'libinput' for 'Dell KB216 Wired Keyboard Consumer Control'
[ 10.134] (**) Dell KB216 Wired Keyboard Consumer Control: always reports core events
[ 10.134] (**) Option "Device" "/dev/input/event6"
[ 10.136] (II) event6 - Dell KB216 Wired Keyboard Consumer Control: is tagged by udev as: Keyboard
[ 10.136] (II) event6 - Dell KB216 Wired Keyboard Consumer Control: device is a keyboard
[ 10.136] (II) event6 - Dell KB216 Wired Keyboard Consumer Control: device removed
[ 10.176] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-10/1-10:1.1/0003:413C:2113.0002/input/input6/event6"
[ 10.176] (II) XINPUT: Adding extended input device "Dell KB216 Wired Keyboard Consumer Control" (type: KEYBOARD, id 12)
[ 10.179] (II) event6 - Dell KB216 Wired Keyboard Consumer Control: is tagged by udev as: Keyboard
[ 10.179] (II) event6 - Dell KB216 Wired Keyboard Consumer Control: device is a keyboard
[ 10.181] (II) config/udev: Adding input device MSI MYSTIC LIGHT (/dev/input/event8)
[ 10.181] (II) No input driver specified, ignoring this device.
[ 10.181] (II) This device may have been added with another device file.
[ 10.182] (II) config/udev: Adding input device PixArt HP 1000 USB Optical Mouse (/dev/input/event7)
[ 10.182] (**) PixArt HP 1000 USB Optical Mouse: Applying InputClass "libinput pointer catchall"
[ 10.182] (II) Using input driver 'libinput' for 'PixArt HP 1000 USB Optical Mouse'
[ 10.182] (**) PixArt HP 1000 USB Optical Mouse: always reports core events
[ 10.182] (**) Option "Device" "/dev/input/event7"
[ 10.184] (II) event7 - PixArt HP 1000 USB Optical Mouse: is tagged by udev as: Mouse
[ 10.185] (II) event7 - PixArt HP 1000 USB Optical Mouse: device is a pointer
[ 10.185] (II) event7 - PixArt HP 1000 USB Optical Mouse: device removed
[ 10.223] (II) libinput: PixArt HP 1000 USB Optical Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.223] (II) libinput: PixArt HP 1000 USB Optical Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.223] (II) libinput: PixArt HP 1000 USB Optical Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.223] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:14.0/usb1/1-9/1-9.3/1-9.3:1.0/0003:03F0:2A41.0003/input/input7/event7"
[ 10.223] (II) XINPUT: Adding extended input device "PixArt HP 1000 USB Optical Mouse" (type: MOUSE, id 13)
[ 10.223] (**) Option "AccelerationScheme" "none"
[ 10.223] (**) PixArt HP 1000 USB Optical Mouse: (accel) selected scheme none/0
[ 10.223] (**) PixArt HP 1000 USB Optical Mouse: (accel) acceleration factor: 2.000
[ 10.223] (**) PixArt HP 1000 USB Optical Mouse: (accel) acceleration threshold: 4
[ 10.226] (II) event7 - PixArt HP 1000 USB Optical Mouse: is tagged by udev as: Mouse
[ 10.226] (II) event7 - PixArt HP 1000 USB Optical Mouse: device is a pointer
[ 10.228] (II) config/udev: Adding input device PixArt HP 1000 USB Optical Mouse (/dev/input/mouse0)
[ 10.228] (II) No input driver specified, ignoring this device.
[ 10.228] (II) This device may have been added with another device file.
[ 10.229] (II) config/udev: Adding input device PC Speaker (/dev/input/event9)
[ 10.229] (II) No input driver specified, ignoring this device.
[ 10.229] (II) This device may have been added with another device file.journal:
http://0x0.st/PXaa.txt
Offline
#13 2026-01-10 23:04:26
- Scimmia
- Fellow
- Registered: 2012-09-01
- Posts: 13,418
Re: X failure with nvidia-590 and nvidia gtx970
What does pacman -Qs 'kernel|nvidia' show?
Offline
#14 2026-01-10 23:05:50
- drudox
- Member
- Registered: 2017-10-01
- Posts: 143
Re: X failure with nvidia-590 and nvidia gtx970
pacman -Qs 'kernel|nvidia'
local/deepin-anything-arch 6.2.10-7
Deepin Anything file search tool, kernel module for Arch kernel
local/dkms 3.3.0-1
Dynamic Kernel Modules System
local/egl-gbm 1.1.2.1-1
The GBM EGL external platform library
local/egl-wayland 4:1.1.21-1
EGLStream-based Wayland external platform
local/egl-wayland2 1.0.0.rc.r53.gf4a2d32-1
EGLStream-based Wayland external platform (2)
local/egl-x11 1.0.4-1
NVIDIA XLib and XCB EGL Platform Library
local/embree 4.4.0-1
Collection of high-performance ray tracing kernels
local/fuse2 2.9.9-5
Interface for userspace programs to export a filesystem to the Linux kernel
local/fuse3 3.17.4-1
Interface for userspace programs to export a filesystem to the Linux kernel
local/iptables 1:1.8.11-2
Linux kernel packet control tool (using legacy interface)
local/kmod 34.2-1
Linux kernel module management tools and library
local/lib32-libdrm 2.4.131-1
Userspace interface to kernel DRM services (32-bit)
local/lib32-libvdpau 1.5-3
Nvidia VDPAU library
local/lib32-nvidia-580xx-utils 580.119.02-1
NVIDIA drivers utilities (32-bit) (580xx)
local/lib32-opencl-nvidia-580xx 580.119.02-1
OpenCL implemention for NVIDIA (32-bit) (580xx)
local/libdrm 2.4.131-1
Userspace interface to kernel DRM services
local/libnetfilter_conntrack 1.0.9-2
Library providing an API to the in-kernel connection tracking state table
local/libnfnetlink 1.0.2-2
Low-level library for netfilter related kernel/userspace communication
local/libsysprof-capture 49.0-1
Kernel based performance profiler - capture library
local/libtraceevent 1:1.8.7-1
Linux kernel trace event library
local/libtracefs 1.8.3-1
Linux kernel trace file system library
local/libvdpau 1.5-3
Nvidia VDPAU library
local/libxnvctrl-580xx 580.119.02-2
NVIDIA NV-CONTROL X extension (580xx)
local/linux 6.18.4.arch1-1
The Linux kernel and modules
local/linux-api-headers 6.18-1
Kernel headers sanitized for use in userspace
local/linux-firmware-nvidia 20251125-2
Firmware files for Linux - Firmware for NVIDIA GPUs and SoCs
local/linux-lts 6.12.64-1
The LTS Linux kernel and modules
local/mtdev 1.1.7-1
A stand-alone library which transforms all variants of kernel MT events to the slotted type B
protocol
local/ndctl 79-1
Utility library for managing the libnvdimm (non-volatile memory device) sub-system in the Linux
kernel
local/nvidia-580xx-dkms 580.119.02-2
NVIDIA kernel modules - module sources (580xx)
local/nvidia-580xx-settings-debug 580.119.02-2
Detached debugging symbols for nvidia-580xx-settings
local/nvidia-580xx-utils 580.119.02-2
NVIDIA drivers utilities (580xx)
local/nvidia-prime 1.0-5
NVIDIA Prime Render Offload configuration and utilities
local/nvidia-settings 590.48.01-1
Tool for configuring the NVIDIA graphics driver
local/opencl-nvidia-580xx 580.119.02-2
OpenCL implemention for NVIDIA (580xx)
local/openvkl 2.0.1-4
Intel® Open Volume Kernel Library
local/sysprof 49.0-1 (gnome-extra)
Kernel based performance profiler
local/texlive-latex 2025.2-3 (texlive)
TeX Live - LaTeX fundamental packages
local/texlive-latexextra 2025.2-3 (texlive)
TeX Live - LaTeX additional packages
local/virtualbox-host-modules-arch 7.2.4-14
Virtualbox host kernel modules for Arch KernelLast edited by drudox (2026-01-10 23:06:45)
Offline
#15 2026-01-10 23:08:15
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 72,057
Re: X failure with nvidia-590 and nvidia gtx970
seth wrote:
You're … lacking linux-lts-headers
https://archlinux.org/packages/core/x86 … s-headers/
https://archlinux.org/packages/core/x86 … x-headers/
Offline
#16 2026-01-10 23:08:48
- Scimmia
- Fellow
- Registered: 2012-09-01
- Posts: 13,418
Re: X failure with nvidia-590 and nvidia gtx970
So you ignored the optional deps of the dkms package that pacman told you about, ignored the dkms wiki page, and ignored what seth told you in posts #6 and #9. Really?
Last edited by Scimmia (2026-01-10 23:09:34)
Offline
#17 2026-01-10 23:09:02
- drudox
- Member
- Registered: 2017-10-01
- Posts: 143
Re: X failure with nvidia-590 and nvidia gtx970
local/nvidia-settings 590.48.01-1
Tool for configuring the NVIDIA graphics driver
???? why 590 ?
Offline
#18 2026-01-10 23:12:54
- drudox
- Member
- Registered: 2017-10-01
- Posts: 143
Re: X failure with nvidia-590 and nvidia gtx970
Scimmia wrote:
So you ignored the optional deps of the dkms package that pacman told you about, ignored the dkms wiki page, and ignored what seth told you in posts #6 and #9. Really?
humm you mean the link he give me ? yes I was reading :\
could you please explain the problem is that I dnt have the : dkms package that pacman told you about ... was yay (btw) where I can found them
Offline
#19 2026-01-10 23:15:24
- Scimmia
- Fellow
- Registered: 2012-09-01
- Posts: 13,418
Re: X failure with nvidia-590 and nvidia gtx970
When you installed the dkms package as a dep of the new package, pacman printed out the optional deps. Did you read them?
Offline
#20 2026-01-10 23:15:52
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 72,057
Re: X failure with nvidia-590 and nvidia gtx970
Because you didn't install https://aur.archlinux.org/packages/nvid … x-settings but that's not the imminent problem
yay (btw) is a pacman wrapping AUR helper - install the kernel header packages, make sure the nvidia dkms modules actually get built
Offline
#21 2026-01-10 23:34:01
- drudox
- Member
- Registered: 2017-10-01
- Posts: 143
Re: X failure with nvidia-590 and nvidia gtx970
sorry mate but where I should read these dependency ?
AUR Explicit (1): nvidia-580xx-dkms-580.119.02-2
Sync Make Dependency (1): patchelf-0.18.0-4
:: PKGBUILD up to date, skipping download: nvidia-580xx-utils
1 nvidia-580xx-utils (Installed) (Build Files Exist)
==> Packages to cleanBuild?
==> [N]one [A]ll [Ab]ort [I]nstalled [No]tInstalled or (1 2 3, 1-3, ^4)
==>
1 nvidia-580xx-utils (Installed) (Build Files Exist)
==> Diffs to show?
==> [N]one [A]ll [Ab]ort [I]nstalled [No]tInstalled or (1 2 3, 1-3, ^4)
==>
==> Making package: nvidia-580xx-utils 580.119.02-2 (Sun 11 Jan 2026 00:29:28 CET)
==> Retrieving sources...
-> Found nvidia-drm-outputclass.conf
-> Found nvidia-utils.sysusers
-> Found nvidia.rules
-> Found systemd-homed-override.conf
-> Found systemd-suspend-override.conf
-> Found nvidia-sleep.conf
-> Found NVIDIA-Linux-x86_64-580.119.02.run
-> Found 0001-Enable-atomic-kernel-modesetting-by-default.patch
-> Found limit-vram-usage
==> WARNING: Skipping verification of source file PGP signatures.
==> Validating source files with sha256sums...
nvidia-drm-outputclass.conf ... Passed
nvidia-utils.sysusers ... Passed
nvidia.rules ... Passed
systemd-homed-override.conf ... Passed
systemd-suspend-override.conf ... Passed
nvidia-sleep.conf ... Passed
NVIDIA-Linux-x86_64-580.119.02.run ... Passed
0001-Enable-atomic-kernel-modesetting-by-default.patch ... Passed
limit-vram-usage ... Passed
:: Remove make dependencies after install? [y/N]
:: (1/1) Parsing SRCINFO: nvidia-580xx-utils
[sudo] password for phobos:
Sorry, try again.
[sudo] password for phobos:
resolving dependencies...
looking for conflicting packages...
Packages (1) patchelf-0.18.0-4
Total Installed Size: 0.26 MiB
:: Proceed with installation? [Y/n]
(1/1) checking keys in keyring [#################################] 100%
(1/1) checking package integrity [#################################] 100%
(1/1) loading package files [#################################] 100%
(1/1) checking for file conflicts [#################################] 100%
(1/1) checking available disk space [#################################] 100%
:: Processing package changes...
(1/1) installing patchelf [#################################] 100%
:: Running post-transaction hooks...
(1/1) Arming ConditionNeedsUpdate...
==> Making package: nvidia-580xx-utils 580.119.02-2 (Sun 11 Jan 2026 00:30:06 CET)
==> Checking runtime dependencies...
==> Checking buildtime dependencies...
==> Retrieving sources...
-> Found nvidia-drm-outputclass.conf
-> Found nvidia-utils.sysusers
-> Found nvidia.rules
-> Found systemd-homed-override.conf
-> Found systemd-suspend-override.conf
-> Found nvidia-sleep.conf
-> Found NVIDIA-Linux-x86_64-580.119.02.run
-> Found 0001-Enable-atomic-kernel-modesetting-by-default.patch
-> Found limit-vram-usage
==> Validating source files with sha256sums...
nvidia-drm-outputclass.conf ... Passed
nvidia-utils.sysusers ... Passed
nvidia.rules ... Passed
systemd-homed-override.conf ... Passed
systemd-suspend-override.conf ... Passed
nvidia-sleep.conf ... Passed
NVIDIA-Linux-x86_64-580.119.02.run ... Passed
0001-Enable-atomic-kernel-modesetting-by-default.patch ... Passed
limit-vram-usage ... Passed
==> Removing existing $srcdir/ directory...
==> Extracting sources...
==> Starting prepare()...
Creating directory NVIDIA-Linux-x86_64-580.119.02
Verifying archive integrity... OK
Uncompressing NVIDIA Accelerated Graphics Driver for Linux-x86_64 580.119.02....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
patching file nvidia-drm/nvidia-drm-linux.c
patching file nvidia-drm/nvidia-drm-os-interface.c
Hunk #1 succeeded at 38 (offset -3 lines).
==> Sources are ready.
-> nvidia-580xx-utils-580.119.02-2 already made -- skipping build
==> Making package: nvidia-580xx-utils 580.119.02-2 (Sun 11 Jan 2026 00:30:12 CET)
==> Checking runtime dependencies...
==> Checking buildtime dependencies...
==> WARNING: Using existing $srcdir/ tree
==> Sources are ready.
loading packages...
warning: nvidia-580xx-dkms-580.119.02-2 is up to date -- reinstalling
resolving dependencies...
looking for conflicting packages...
Packages (1) nvidia-580xx-dkms-580.119.02-2
Total Installed Size: 117.83 MiB
Net Upgrade Size: 0.00 MiB
:: Proceed with installation? [Y/n]
(1/1) checking keys in keyring [#################################] 100%
(1/1) checking package integrity [#################################] 100%
(1/1) loading package files [#################################] 100%
(1/1) checking for file conflicts [#################################] 100%
(1/1) checking available disk space [#################################] 100%
:: Running pre-transaction hooks...
(1/1) Remove upgraded DKMS modules
:: Processing package changes...
(1/1) reinstalling nvidia-580xx-dkms [#################################] 100%
:: Running post-transaction hooks...
(1/3) Arming ConditionNeedsUpdate...
(2/3) Install DKMS modules
==> ERROR: Missing part.txt kernel headers for module nvidia/580.119.02.
==> ERROR: Missing sys kernel headers for module nvidia/580.119.02.
==> ERROR: Missing etc kernel headers for module nvidia/580.119.02.
==> ERROR: Missing mnt3 kernel headers for module nvidia/580.119.02.
==> ERROR: Missing mnt2 kernel headers for module nvidia/580.119.02.
==> ERROR: Missing cmd.txt kernel headers for module nvidia/580.119.02.
==> ERROR: Missing tmp kernel headers for module nvidia/580.119.02.
==> ERROR: Missing yay kernel headers for module nvidia/580.119.02.
==> ERROR: Missing home kernel headers for module nvidia/580.119.02.
==> ERROR: Missing boot kernel headers for module nvidia/580.119.02.
==> ERROR: Missing mnt kernel headers for module nvidia/580.119.02.
==> ERROR: Missing part2.txt kernel headers for module nvidia/580.119.02.
==> ERROR: Missing proc kernel headers for module nvidia/580.119.02.
==> ERROR: Missing media kernel headers for module nvidia/580.119.02.
==> ERROR: Missing tool_efi kernel headers for module nvidia/580.119.02.
==> ERROR: Missing run kernel headers for module nvidia/580.119.02.
==> ERROR: Missing lib kernel headers for module nvidia/580.119.02.
==> ERROR: Missing root kernel headers for module nvidia/580.119.02.
==> ERROR: Missing dev kernel headers for module nvidia/580.119.02.
==> ERROR: Missing sbin kernel headers for module nvidia/580.119.02.
==> ERROR: Missing opt kernel headers for module nvidia/580.119.02.
==> ERROR: Missing srv kernel headers for module nvidia/580.119.02.
==> ERROR: Missing lost+found kernel headers for module nvidia/580.119.02.
==> ERROR: Missing lib64 kernel headers for module nvidia/580.119.02.
==> ERROR: Missing bin kernel headers for module nvidia/580.119.02.
==> ERROR: Missing usr kernel headers for module nvidia/580.119.02.
==> ERROR: Missing hostlvm kernel headers for module nvidia/580.119.02.
==> ERROR: Missing grub2-sh-Jof39p kernel headers for module nvidia/580.119.02.
==> ERROR: Missing var kernel headers for module nvidia/580.119.02.
(3/3) Updating linux initcpios...
==> Building image from preset: /etc/mkinitcpio.d/linux-lts.preset: 'default'
==> Using default configuration file: '/etc/mkinitcpio.conf'
-> -k /boot/vmlinuz-linux-lts -g /boot/initramfs-linux-lts.img
==> Starting build: '6.12.64-1-lts'
-> Running build hook: [base]
-> Running build hook: [systemd]
-> Running build hook: [autodetect]
-> Running build hook: [microcode]
-> Running build hook: [modconf]
-> Running build hook: [kms]
-> Running build hook: [keyboard]
-> Running build hook: [keymap]
-> Running build hook: [sd-vconsole]
-> Running build hook: [block]
-> Running build hook: [filesystems]
-> Running build hook: [fsck]
==> Generating module dependencies
==> Creating zstd-compressed initcpio image: '/boot/initramfs-linux-lts.img'
-> Early uncompressed CPIO image generation successful
==> Initcpio image generation successful
==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'default'
==> Using default configuration file: '/etc/mkinitcpio.conf'
-> -k /boot/vmlinuz-linux -g /boot/initramfs-linux.img
==> Starting build: '6.18.4-arch1-1'
-> Running build hook: [base]
-> Running build hook: [systemd]
-> Running build hook: [autodetect]
-> Running build hook: [microcode]
-> Running build hook: [modconf]
-> Running build hook: [kms]
-> Running build hook: [keyboard]
-> Running build hook: [keymap]
-> Running build hook: [sd-vconsole]
-> Running build hook: [block]
-> Running build hook: [filesystems]
-> Running build hook: [fsck]
==> Generating module dependencies
==> Creating zstd-compressed initcpio image: '/boot/initramfs-linux.img'
-> Early uncompressed CPIO image generation successful
==> Initcpio image generation successfulOffline
#22 2026-01-10 23:36:24
- Scimmia
- Fellow
- Registered: 2012-09-01
- Posts: 13,418
Re: X failure with nvidia-590 and nvidia gtx970
You already have it installed, of course it's not pulling it in again.
I'm done, you can't seem to read anything. You've ignored everything, even seth telling you over and over how to fix it. Some people just can't be helped.
Offline
#23 2026-01-10 23:38:51
- drudox
- Member
- Registered: 2017-10-01
- Posts: 143
Re: X failure with nvidia-590 and nvidia gtx970
Scimmia wrote:
You already have it installed, of course it's not pulling it in again.
I'm done, you can't seem to read anything. You've ignored everything, even seth telling you over and over how to fix it. Some people just can't be helped.
come on man ... sorry I was trying to fix it alone since 8.00am .. now it's 00.38 a bit tired ?? btw I install the linux-header and now dkms works .. wait
Offline
#24 2026-01-10 23:39:24
- drudox
- Member
- Registered: 2017-10-01
- Posts: 143
Re: X failure with nvidia-590 and nvidia gtx970
dkms status
nvidia/580.119.02, 6.12.64-1-lts, x86_64: installed
nvidia/580.119.02, 6.18.4-arch1-1, x86_64: installedOffline
#25 2026-01-10 23:40:49
- seth
- Member
- From: Don't DM me only for attention
- Registered: 2012-09-03
- Posts: 72,057
Re: X failure with nvidia-590 and nvidia gtx970
Please always remember to mark resolved threads by editing your initial posts subject - so others will know that there's no task left, but maybe a solution to find.
Thanks.
Offline